Cluster API

The Cluster driver is separated into three layers:

• QCoDeS driver: Instrument driver based on QCoDeS and the instrument’s native interface.

• Native interface: Instrument API that provides control over the instrument and is an extension of the the SCPI interface.

• SCPI interface: Instrument API based on the SCPI standard which in turn is based on IEEE488.2.

QCoDeS driver

class qblox_instruments.Cluster(*args: Any, **kwargs: Any)

Bases: Cluster, Instrument

This class connects QCoDeS to the Cluster native interface.

__init__(name: str, identifier: str | None = None, port: int | None = None, debug: int | None = None, dummy_cfg: Dict | None = None)

Creates Cluster QCoDeS class and adds all relevant instrument parameters. These instrument parameters call the associated methods provided by the native interface.

Parameters:

• name (str) – Instrument name.

• identifier (Optional[str]) – Instrument identifier. See resolve(). If None, the instrument is identified by name.

• port (Optional[int]) – Override for the TCP port through which we should connect.

• debug (Optional[int]) – Debug level (0 | None = normal, 1 = no version check, >1 = no version or error checking).

• dummy_cfg (Optional[Dict]) – Configure as dummy using this configuration. For each slot that needs to be occupied by a module add the slot index as key and specify the type of module in the slot using the type ClusterType.

property modules: List

Get list of modules.

Returns:

List of modules.

Return type:

list

get_connected_modules(filter_fn: Callable[[Module], bool] | None = None) → Dict[int, Module]

Get the currently connected modules for each occupied slot in the Cluster.

A selection of modules can be made by passing a filter function. For example:

cluster.get_connected_modules(
    filter_fn = lambda mod: mod.is_qrm_type and not mod.is_rf_type
)

Parameters:

filter_fn – Optional filter function that must return True for the modules that should be included in the return value, and False otherwise.

Returns:

Dictionary with key-value pairs consisting of slot numbers and corresponding Module objects. Only contains entries for modules that are present and match the filter_fn.

Return type:

dict

reset() → None

Resets device, invalidates QCoDeS parameter cache and clears all status and event registers (see SCPI).

disconnect_outputs(slot: int) → None

Disconnects all outputs from the waveform generator paths of the sequencers.

Parameters:

slot (int) – Slot index

disconnect_inputs(slot: int) → None

Disconnects all inputs from the acquisition paths of the sequencers.

Parameters:

slot (int) – Slot index

connect_sequencer(slot: int, sequencer: int, *connections: str) → None

Makes new connections between the indexed sequencer and some inputs and/or outputs. This will fail if a requested connection already existed, or if the connection could not be made due to a conflict with an existing connection (hardware constraints). In such a case, the channel map will not be affected.

Parameters:

• slot (int) – Slot index

• sequencer (int) – Sequencer index

• *connections (str) – Zero or more connections to make, each specified using a string. The string should have the format <direction><channel> or <direction><I-channel>_<Q-channel>. <direction> must be in to make a connection between an input and the acquisition path, out to make a connection from the waveform generator to an output, or io to do both. The channels must be integer channel indices. If only one channel is specified, the sequencer operates in real mode; if two channels are specified, it operates in complex mode.

Raises:

• RuntimeError – If the connection command could not be completed due to a conflict.

• ValueError – If parsing of a connection fails.

QCoDeS instrument parameters

QCoDeS parameters generated by Cluster.

Cluster.IDN()

Please see QCoDeS for a description.

Properties:

• value: Anything

Cluster.led_brightness()

Sets/gets frontpanel LED brightness.

Properties:

• value: Enum: {‘medium’, ‘low’, ‘off’, ‘high’}

Cluster.reference_source()

Sets/gets reference source (‘internal’ = internal 10 MHz, ‘external’ = external 10 MHz).

Properties:

• value: Enum: {‘internal’, ‘external’}

Cluster.ext_trigger_input_delay()

Sets/gets the delay of the external input trigger in picoseconds.

Properties:

• unit: ps

• value: Ints 0<=v<=1209, Multiples of 39

Cluster.ext_trigger_input_trigger_en()

Enable/disable the external input trigger.

Properties:

• value: Boolean

Cluster.ext_trigger_input_trigger_address()

Sets/gets the external input trigger address to which the input trigger is mapped to the trigger network (T1 to T15).

Properties:

• value: Numbers 1<=v<=15

Cluster.trigger1_monitor_count()

Gets the trigger monitor count from trigger address T1.

Properties:

• value: on

Cluster.trigger2_monitor_count()

Gets the trigger monitor count from trigger address T2.

Properties:

• value: on

Cluster.trigger3_monitor_count()

Gets the trigger monitor count from trigger address T3.

Properties:

• value: on

Cluster.trigger4_monitor_count()

Gets the trigger monitor count from trigger address T4.

Properties:

• value: on

Cluster.trigger5_monitor_count()

Gets the trigger monitor count from trigger address T5.

Properties:

• value: on

Cluster.trigger6_monitor_count()

Gets the trigger monitor count from trigger address T6.

Properties:

• value: on

Cluster.trigger7_monitor_count()

Gets the trigger monitor count from trigger address T7.

Properties:

• value: on

Cluster.trigger8_monitor_count()

Gets the trigger monitor count from trigger address T8.

Properties:

• value: on

Cluster.trigger9_monitor_count()

Gets the trigger monitor count from trigger address T9.

Properties:

• value: on

Cluster.trigger10_monitor_count()

Gets the trigger monitor count from trigger address T10.

Properties:

• value: on

Cluster.trigger11_monitor_count()

Gets the trigger monitor count from trigger address T11.

Properties:

• value: on

Cluster.trigger12_monitor_count()

Gets the trigger monitor count from trigger address T12.

Properties:

• value: on

Cluster.trigger13_monitor_count()

Gets the trigger monitor count from trigger address T13.

Properties:

• value: on

Cluster.trigger14_monitor_count()

Gets the trigger monitor count from trigger address T14.

Properties:

• value: on

Cluster.trigger15_monitor_count()

Gets the trigger monitor count from trigger address T15.

Properties:

• value: on

Cluster.trigger_monitor_latest()

Gets the trigger address which was triggered last (T1 to T15).

Properties:

• value: on

arm_sequencer(slot: int | None = None, sequencer: int | None = None) → None

Prepare the indexed sequencer to start by putting it in the armed state. If no sequencer index is given, all sequencers are armed. Any sequencer that was already running is stopped and rearmed. If an invalid sequencer index is given, an error is set in system error.

Parameters:

• slot (Optional[int]) – The slot index of the module being referred to.

• sequencer (Optional[int]) – Sequencer index.

Raises:

RuntimeError – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

clear() → None

Clear all status and event registers (see SCPI).

Parameters:

None –

Return type:

None

Raises:

• Exception – Invalid input parameter type.

• Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

clear_sequencer_flags(slot: int | None = None, sequencer: int | None = None) → None

Clear flags

Parameters:

• slot (Optional[int]) – The slot index of the module being referred to.

• sequencer (int) – Sequencer index.

connect_sequencer(slot: int, sequencer: int, *connections: str) → None

Makes new connections between the indexed sequencer and some inputs and/or outputs. This will fail if a requested connection already existed, or if the connection could not be made due to a conflict with an existing connection (hardware constraints). In such a case, the channel map will not be affected.

Parameters:

• slot (int) – Slot index

• sequencer (int) – Sequencer index

• *connections (str) – Zero or more connections to make, each specified using a string. The string should have the format <direction><channel> or <direction><I-channel>_<Q-channel>. <direction> must be in to make a connection between an input and the acquisition path, out to make a connection from the waveform generator to an output, or io to do both. The channels must be integer channel indices. If only one channel is specified, the sequencer operates in real mode; if two channels are specified, it operates in complex mode.

Raises:

• RuntimeError – If the connection command could not be completed due to a conflict.

• ValueError – If parsing of a connection fails.

delete_acquisition_data(slot: int, sequencer: int, name: str = '', all: bool = False) → None

Delete data from an acquisition specified by name in the acquisition list of indexed sequencer or delete data in all acquisitions if all is True.

Parameters:

• slot (int) – The slot index of the module being referred to.

• sequencer (int) – Sequencer index.

• name (str) – Weight name

Raises:

NotImplementedError – Functionality not available on this module.

delete_dummy_binned_acquisition_data(slot_idx: int, sequencer: int | None = None, acq_index_name: str | None = None)

Delete all dummy binned acquisition data for the dummy.

Parameters:

• slot_idx (int) – Slot of the hardware you want to set the data to on a cluster.

• sequencer (Optional[int]) – Sequencer.

• acq_index_name (Optional[str]) – Acquisition index name.

delete_dummy_scope_acquisition_data(slot_idx: int, sequencer: int | None)

Delete dummy scope acquisition data for the dummy.

Parameters:

• slot_idx (int) – Slot of the hardware you want to set the data to on a cluster.

• sequencer (Union[int, None]) – Sequencer.

disconnect_inputs(slot: int) → None

Disconnects all inputs from the acquisition paths of the sequencers.

Parameters:

slot (int) – Slot index

disconnect_outputs(slot: int) → None

Disconnects all outputs from the waveform generator paths of the sequencers.

Parameters:

slot (int) – Slot index

get_acquisition_state(slot: int, sequencer: int, timeout: int = 0, timeout_poll_res: float = 0.02) → bool

Return acquisition binning completion state of the indexed sequencer. If an invalid sequencer is given, an error is set in system error. If the timeout is set to zero, the function returns the state immediately. If a positive non-zero timeout is set, the function blocks until the acquisition binning completes. If the acquisition hasn’t completed before the timeout expires, a TimeoutError is thrown. Note that when sequencer state checking is enabled, the sequencer state is checked using get_sequencer_state with the selected timeout period first and then the acquisition state is checked with the same timeout period. This means that the total timeout period is two times the set timeout period.

Parameters:

• slot (int) – The slot index of the module being referred to.

• sequencer (int) – Sequencer index.

• timeout (int) – Timeout in minutes.

• timeout_poll_res (float) – Timeout polling resolution in seconds.

• check_seq_state (bool) – Check if sequencer is done before checking acquisition state.

Returns:

Indicates the acquisition binning completion state (False = uncompleted, True = completed).

Return type:

bool

Raises:

• TimeoutError – Timeout

• NotImplementedError – Functionality not available on this module.

get_acquisition_status(slot: int, sequencer: int, timeout: int = 0, timeout_poll_res: float = 0.02) → bool

Return acquisition binning completion status of the indexed sequencer. If an invalid sequencer is given, an error is set in system error. If the timeout is set to zero, the function returns the status immediately. If a positive non-zero timeout is set, the function blocks until the acquisition binning completes. If the acquisition hasn’t completed before the timeout expires, a TimeoutError is thrown. Note that when sequencer state checking is enabled, the sequencer state is checked using get_sequencer_status with the selected timeout period first and then the acquisition status is checked with the same timeout period. This means that the total timeout period is two times the set timeout period.

Parameters:

• slot (int) – The slot index of the module being referred to.

• sequencer (int) – Sequencer index.

• timeout (int) – Timeout in minutes.

• timeout_poll_res (float) – Timeout polling resolution in seconds.

• check_seq_state (bool) – Check if sequencer is done before checking acquisition status.

Returns:

Indicates the acquisition binning completion status (False = uncompleted, True = completed).

Return type:

bool

Raises:

• TimeoutError – Timeout

• NotImplementedError – Functionality not available on this module.

get_acquisitions(slot: int, sequencer: int) → Dict

Get all acquisitions in acquisition lists of indexed sequencer. The acquisition scope and bin data is normalized to a range of -1.0 to 1.0 taking both the bit widths of the processing path and average count into considaration. For the binned integration results, the integration length is not handled during normalization and therefore these values have to be divided by their respective integration lenghts. The returned dictionary is structured as follows:

• name: acquisition name

  • index: acquisition index used by the sequencer Q1ASM program to refer to the acquisition.

  • acquisition: acquisition dictionary

    • scope: Scope data

      • path0: input path 0

        • data: acquisition samples in a range of 1.0 to -1.0.

        • out-of-range: out-of-range indication for the entire acquisition (False = in-range, True = out-of-range).

        • avg_cnt: number of averages.

      • path1: input path 1

        • data: acquisition samples in a range of 1.0 to -1.0.

        • out-of-range: out-of-range indication for the entire acquisition (False = in-range, True = out-of-range).

        • avg_cnt: number of averages.

    • bins: bin data

      • integration: integration data

        • path_0: input path 0 integration result bin list

        • path_1: input path 1 integration result bin list

      • threshold: threshold result bin list

      • valid: list of valid indications per bin

      • avg_cnt: list of number of averages per bin

Parameters:

• slot (int) – The slot index of the module being referred to.

• sequencer (int) – Sequencer index.

Returns:

Dictionary with acquisitions.

Return type:

dict

Raises:

NotImplementedError – Functionality not available on this module.

get_assembler_log(slot: int) → str

Get assembler log.

Parameters:

slot (int) – slot index.

Returns:

Assembler log.

Return type:

str

Raises:

• Exception – Invalid input parameter type.

• Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_assembler_status(slot: int) → bool

Get assembler status. Refer to the assembler log to get more information regarding the assembler result.

Parameters:

slot (int) – slot index.

Returns:

Assembler status (False = failed, True = success).

Return type:

bool

Raises:

• Exception – Invalid input parameter type.

• Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_connected_modules(filter_fn: Callable[[qblox_instruments.qcodes_drivers.module.Module], bool] | None = None) → Dict[int, qblox_instruments.qcodes_drivers.module.Module]

Get the currently connected modules for each occupied slot in the Cluster.

A selection of modules can be made by passing a filter function. For example:

cluster.get_connected_modules(
    filter_fn = lambda mod: mod.is_qrm_type and not mod.is_rf_type
)

Parameters:

filter_fn – Optional filter function that must return True for the modules that should be included in the return value, and False otherwise.

Returns:

Dictionary with key-value pairs consisting of slot numbers and corresponding Module objects. Only contains entries for modules that are present and match the filter_fn.

Return type:

dict

get_current_afe_temperature(slot: int) → float

Get current AFE temperature.

Parameters:

slot (int) – slot index.

Returns:

current

Return type:

float

Raises:

• Exception – Invalid input parameter type.

• Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_current_bp_temperature_0() → float

Get current backplane board temperature from sensor 0 (inside device).

Parameters:

None –

Returns:

Current backplane board temperature from sensor 0.

Return type:

float

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_current_bp_temperature_1() → float

Get current backplane board temperature from sensor 1 (inside device).

Parameters:

None –

Returns:

Current backplane board temperature from sensor 1.

Return type:

float

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_current_bp_temperature_2() → float

Get current backplane board temperature from sensor 2 (inside device).

Parameters:

None –

Returns:

Current backplane board temperature from sensor 2.

Return type:

float

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_current_carrier_temperature(slot: int) → float

Get current carrier board temperature (inside device).

Parameters:

slot (int) – slot index.

Returns:

Current carrier board temperature.

Return type:

float

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_current_fpga_temperature(slot: int) → float

Get current FPGA junction temperature (inside device).

Parameters:

slot (int) – slot index.

Returns:

Current FPGA junction temperature.

Return type:

float

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_current_lo_temperature(slot: int) → float

Get current LO temperature.

Parameters:

slot (int) – slot index.

Returns:

current

Return type:

float

Raises:

• Exception – Invalid input parameter type.

• Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_ip_config() → str

Returns the IP address configuration that will go into effect when the device reboots.

Parameters:

None –

Returns:

IP configuration. Can be one of the following things:

• an IPv4 address including prefix length, for example 192.168.0.2/24, - the string dhcp to enable IPv4 DHCP, - an IPv6 address including prefix length, for example 1:2::3:4/64, or - a semicolon-separated combination of an IPv4 configuration (IP address or dhcp) and an IPv6 address.

Return type:

str

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_maximum_afe_temperature(slot: int) → float

Get maximum AFE temperature.

Parameters:

slot (int) – slot index.

Returns:

maximum

Return type:

float

Raises:

• Exception – Invalid input parameter type.

• Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_maximum_bp_temperature_0() → float

Get maximum backplane board temperature from sensor 0 since boot or clear (inside device).

Parameters:

None –

Returns:

Maximum backplane board temperature from sensor 0.

Return type:

float

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_maximum_bp_temperature_1() → float

Get maximum backplane board temperature from sensor 1 since boot or clear (inside device).

Parameters:

None –

Returns:

Maximum backplane board temperature from sensor 1.

Return type:

float

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_maximum_bp_temperature_2() → float

Get maximum backplane board temperature from sensor 2 since boot or clear (inside device).

Parameters:

None –

Returns:

Maximum backplane board temperature from sensor 2.

Return type:

float

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_maximum_carrier_temperature(slot: int) → float

Get maximum carrier board temperature since boot or clear (inside device).

Parameters:

slot (int) – slot index.

Returns:

Maximum carrier board temperature.

Return type:

float

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_maximum_fpga_temperature(slot: int) → float

Get maximum FPGA junction temperature since boot or clear (inside device).

Parameters:

slot (int) – slot index.

Returns:

Maximum FPGA junction temperature.

Return type:

float

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_maximum_lo_temperature(slot: int) → float

Get maximum LO temperature.

Parameters:

slot (int) – slot index.

Returns:

maximum

Return type:

float

Raises:

• Exception – Invalid input parameter type.

• Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_name() → str

Returns the customer-specified name of the instrument.

Parameters:

None –

Returns:

The name of the device.

Return type:

str

Raises:

• Exception – Invalid input parameter type.

• Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_num_system_error() → int

Get number of system errors (see SCPI).

Parameters:

None –

Returns:

Current number of system errors.

Return type:

int

get_operation_complete() → bool

Get operation complete state (see SCPI).

Parameters:

None –

Returns:

Operation complete state (False = running, True = completed).

Return type:

bool

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_operation_condition() → int

Get status operation condition register (see SCPI).

Parameters:

None –

Returns:

Status operation condition register.

Return type:

int

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_operation_enable() → int

Get status operation enable register (see SCPI).

Parameters:

None –

Returns:

Status operation enable register.

Return type:

int

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_operation_events() → int

Get status operation event register (see SCPI).

Parameters:

None –

Returns:

Status operation event register.

Return type:

int

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_questionable_condition() → int

Get status questionable condition register (see SCPI).

Parameters:

None –

Returns:

Status questionable condition register.

Return type:

int

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_questionable_enable() → int

Get status questionable enable register (see SCPI).

Parameters:

None –

Returns:

Status questionable enable register.

Return type:

int

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_questionable_event() → int

Get status questionable event register (see SCPI).

Parameters:

None –

Returns:

Status questionable event register.

Return type:

int

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_sequencer_state(slot: int, sequencer: int, timeout: int = 0, timeout_poll_res: float = 0.02) → qblox_instruments.native.generic_func.SequencerState

Get the sequencer state. If an invalid sequencer index is given, an error is set in system error. If the timeout is set to zero, the function returns the state immediately. If a positive non-zero timeout is set, the function blocks until the sequencer completes. If the sequencer hasn’t stopped before the timeout expires, a TimeoutError is thrown.

Parameters:

• slot (int) – The slot index of the module being referred to.

• sequencer (int) – Sequencer index.

• timeout (int) – Timeout in minutes.

• timeout_poll_res (float) – Timeout polling resolution in seconds.

Returns:

Tuple containing sequencer status and corresponding flags.

Return type:

SequencerState

Raises:

TimeoutError – Timeout

get_sequencer_status(slot: int, sequencer: int, timeout: int = 0, timeout_poll_res: float = 0.02) → qblox_instruments.native.generic_func.SequencerStatus

Get the sequencer status. If an invalid sequencer index is given, an error is set in system error. If the timeout is set to zero, the function returns the state immediately. If a positive non-zero timeout is set, the function blocks until the sequencer completes. If the sequencer hasn’t stopped before the timeout expires, a TimeoutError is thrown.

Parameters:

• slot (int) – The slot index of the module being referred to.

• sequencer (int) – Sequencer index.

• timeout (int) – Timeout in minutes.

• timeout_poll_res (float) – Timeout polling resolution in seconds.

Returns:

Tuple containing sequencer status and corresponding flags.

Return type:

SequencerState

Raises:

TimeoutError – Timeout

get_service_request_enable() → int

Get service request enable register. The register is cleared after reading it (see SCPI).

Parameters:

None –

Returns:

Service request enable register.

Return type:

int

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_standard_event_status() → int

Get standard event status register. The register is cleared after reading it (see SCPI).

Parameters:

None –

Returns:

Standard event status register.

Return type:

int

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_standard_event_status_enable() → int

Get standard event status enable register. The register is cleared after reading it (see SCPI).

Parameters:

None –

Returns:

Standard event status enable register.

Return type:

int

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_status_byte() → int

Get status byte register. Register is only cleared when feeding registers are cleared (see SCPI).

Parameters:

None –

Returns:

Status byte register.

Return type:

int

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_system_error() → str

Get system error from queue (see SCPI).

Parameters:

None –

Returns:

System error description string.

Return type:

str

get_system_state() → qblox_instruments.native.generic_func.SystemState

Get general system state and convert it to a SystemState.

Returns:

Tuple containing general system status and corresponding flags.

Return type:

SystemStatus

get_system_status() → qblox_instruments.native.generic_func.SystemStatus

Get general system status and convert it to a SystemStatus.

Returns:

Tuple containing general system status and corresponding flags.

Return type:

SystemStatus

get_system_version() → str

Get SCPI system version (see SCPI).

Parameters:

None –

Returns:

SCPI system version.

Return type:

str

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_trg_in_delay() → int

Get external trigger input delay

Parameters:

None –

Returns:

Current status of the external trigger input delay (ps), in steps of 39 ps.

Return type:

int

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_trg_in_map_addr() → int

Get external trigger input map address

Parameters:

None –

Returns:

Current status of the external trigger input map address

Return type:

int

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_trg_in_map_en() → bool

Get external trigger input map enable

Parameters:

None –

Returns:

Current status of the external trigger input map enable

Return type:

bool

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_trigger_monitor_count(address: int) → int

Get trigger monitor count

Parameters:

address (int) – Address of the trigger

Returns:

Current status of trigger monitor counter

Return type:

int

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_trigger_monitor_latest() → int

Get trigger monitor latest value

Parameters:

None –

Returns:

Latest value from the trigger monitor counter

Return type:

int

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_waveforms(slot: int, sequencer: int) → Dict

Get all waveforms and weigths in the AWG waveform list of indexed sequencer. The returned dictionary is structured as follows:

• name: waveform name.

  • data: waveform samples in a range of 1.0 to -1.0.

  • index: waveform index used by the sequencer Q1ASM program to refer

    to the waveform.

Parameters:

• slot (int) – The slot index of the module being referred to.

• sequencer (int) – Sequencer index.

Returns:

Dictionary with waveforms.

Return type:

dict

get_weights(slot: int, sequencer: int) → Dict

Get all weigths in the acquisition weight lists of indexed sequencer. The returned dictionary is structured as follows:

-name : weight name.

• data: weight samples in a range of 1.0 to -1.0.

• index: weight index used by the sequencer Q1ASM program to refer

  to the weight.

Parameters:

• slot (int) – The slot index of the module being referred to.

• sequencer (int) – Sequencer index.

Returns:

Dictionary with weights.

Return type:

dict

Raises:

NotImplementedError – Functionality not available on this module.

identify() → None

Toggle frontpanel LEDs to visually identify the instrument.

Parameters:

None –

Return type:

None

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

property instrument_class(self) → qblox_instruments.types.InstrumentClass

Get instrument class (e.g. Cluster).

Returns:

Instrument class

Return type:

InstrumentClass

property instrument_type(self) → qblox_instruments.types.InstrumentType

Get instrument type (e.g. MM, QRM, QCM).

Returns:

Instrument type

Return type:

InstrumentType

property modules(self) → List

Get list of modules.

Returns:

List of modules.

Return type:

list

preset_system_status() → None

Preset system status registers. Connects general system status flags for PLL unlock and temperature out-of-range indications to event status enable, status questionable temperature and status questionable frequency registers respectively (see SCPI).

Parameters:

None –

Return type:

None

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

reboot() → None

Reboots the instrument.

Parameters:

None –

Return type:

None

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

reset() → None

Resets device, invalidates QCoDeS parameter cache and clears all status and event registers (see SCPI).

reset_trigger_monitor_count(address: int) → None

Reset external trigger monitor counter

Parameters:

address (int) – Address of the trigger which count has to be reset

Return type:

None

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

set_dummy_binned_acquisition_data(slot_idx: int, sequencer: int, acq_index_name: str, data: Iterable[qblox_instruments.ieee488_2.dummy_transport.DummyBinnedAcquisitionData | None])

Set dummy binned acquisition data for the dummy.

Parameters:

• slot_idx (int) – Slot of the hardware you want to set the data to on a cluster.

• sequencer (int) – Sequencer.

• acq_index_name (str) – Acquisition index name.

• data (Iterable[Union[DummyBinnedAcquisitionData, None]]) – Dummy data for the binned acquisition. An iterable of all the bin values.

set_dummy_scope_acquisition_data(slot_idx: int, sequencer: int | None, data: qblox_instruments.ieee488_2.dummy_transport.DummyScopeAcquisitionData)

Set dummy scope acquisition data for the dummy.

Parameters:

• slot_idx (int) – Slot of the hardware you want to set the data to on a cluster.

• sequencer (Union[int, None]) – Sequencer.

• data (DummyScopeAcquisitionData) – Dummy data for the scope acquisition.

set_ip_config(config: str) → None

Reconfigures the IP address of this device. The configuration will not go into effect until reboot() is called or the device is power-cycled.

Parameters:

config (str) –

IP configuration. May be one of the following things:

• an IPv4 address including prefix length, for example 192.168.0.2/24, - the string dhcp to enable IPv4 DHCP, - an IPv6 address including prefix length, for example 1:2::3:4/64, or - a semicolon-separated combination of an IPv4 configuration (IP address or dhcp) and an IPv6 address.

Return type:

None

Raises:

• Exception – Invalid input parameter type.

• Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

set_name(name: str) → None

Sets the customer-specified name of the instrument. The name must not contain any newlines, backslashes, or double quotes.

Parameters:

name (str) – The new name for the device.

Return type:

None

Raises:

• Exception – Invalid input parameter type.

• Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

set_operation_complete() → None

Set device in operation complete query active state (see SCPI).

Parameters:

None –

Return type:

None

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

set_operation_enable(reg: int) → None

Set status operation enable register (see SCPI).

Parameters:

reg (int) – Status operation enable register.

Return type:

None

Raises:

• Exception – Invalid input parameter type.

• Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

set_questionable_enable(reg: int) → None

Set status questionable enable register (see SCPI).

Parameters:

reg (int) – Status questionable enable register.

Return type:

None

Raises:

• Exception – Invalid input parameter type.

• Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

set_service_request_enable(reg: int) → None

Set service request enable register (see SCPI).

Parameters:

reg (int) – Service request enable register.

Return type:

None

Raises:

• Exception – Invalid input parameter type.

• Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

set_standard_event_status_enable(reg: int) → None

Set standard event status enable register (see SCPI).

Parameters:

reg (int) – Standard event status enable register.

Return type:

None

Raises:

• Exception – Invalid input parameter type.

• Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

set_trg_in_delay(trg_in_delay: int) → None

Set external trigger input delay

Parameters:

trg_in_delay (int) – External trigger input delay (ps), in steps of 39 ps.

Return type:

None

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

set_trg_in_map_addr(trg_in_map_addr: int) → None

Set external trigger input map enable

Parameters:

trg_in_map_addr (int) – External trigger input map address

Return type:

None

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

set_trg_in_map_en(trg_in_map_en: bool) → None

Set external trigger input map enable

Parameters:

trg_in_map_en (bool) – External trigger input map enable

Return type:

None

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

start_adc_calib(slot: int) → None

Calibrates ADC delay and offset values. This method sets the correct delay values for every input data index (IO data lane) in order to avoid timing violations which occur while sampling ADC data. It also calibrates offsets internal to the ADC.

Parameters:

slot (int) – slot index.

Return type:

None

Raises:

• Exception – Invalid input parameter type.

• Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

start_sequencer(slot: int | None = None, sequencer: int | None = None) → None

Start the indexed sequencer, thereby putting it in the running state. If an invalid sequencer index is given or the indexed sequencer was not yet armed, an error is set in system error. If no sequencer index is given, all armed sequencers are started and any sequencer not in the armed state is ignored. However, if no sequencer index is given and no sequencers are armed, and error is set in system error.

Parameters:

• slot (Optional[int]) – The slot index of the module being referred to.

• sequencer (Optional[int]) – Sequencer index.

Raises:

RuntimeError – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

stop_sequencer(slot: int | None = None, sequencer: int | None = None) → None

Stop the indexed sequencer, thereby putting it in the stopped state. If an invalid sequencer index is given, an error is set in system error. If no sequencer index is given, all sequencers are stopped.

Parameters:

• slot (Optional[int]) – The slot index of the module being referred to.

• sequencer (Optional[int]) – Sequencer index.

Raises:

RuntimeError – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

store_scope_acquisition(slot: int, sequencer: int, name: str) → None

After an acquisition has completed, store the scope acquisition results in the acquisition specified by name of the indexed sequencers. If an invalid sequencer index is given an error is set in system error. To get access to the acquisition results, the sequencer will be stopped when calling this function.

Parameters:

• slot (int) – The slot index of the module being referred to.

• sequencer (int) – Sequencer index.

• name (str) – Acquisition name.

Raises:

NotImplementedError – Functionality not available on this module.

test() → bool

Run self-test. Currently not implemented (see SCPI).

Parameters:

None –

Returns:

Test result (False = failed, True = success).

Return type:

bool

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

wait() → None

Wait until operations completed before continuing (see SCPI).

Parameters:

None –

Return type:

None

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

QCoDeS module parameters

Besides instrument parameters, the Cluster also has parameters for each module in the Cluster which are described in QCM-QRM API.

Native interface

class qblox_instruments.native.Cluster(identifier: str, port: int | None = None, debug: int | None = None, dummy_cfg: Dict | None = None)

Bases: Cluster

Class that provides the native API for the Cluster. It provides methods to control all functions and features provided by the Cluster.

Note that the bulk of the functionality of this class is contained in the generic_func module so that this functionality can be shared between instruments.

__init__(identifier: str, port: int | None = None, debug: int | None = None, dummy_cfg: Dict | None = None)

Creates Cluster native interface object.

Parameters:

• identifier (str) – Instrument identifier. See resolve() for more information.

• port (Optional[int]) – Instrument port. If None, this will be determined automatically.

• debug (Optional[int]) – Debug level (0 | None = normal, 1 = no version check, >1 = no version or error checking).

• dummy_cfg (Optional[Dict]) – Configure as dummy using this configuration. For each slot that needs to be occupied by a module add the slot index as key and specify the type of module in the slot using the type ClusterType.

Raises:

• RuntimeError – Instrument cannot be reached due to invalid IP configuration.

• ConnectionError – Instrument type is not supported.

property instrument_class: InstrumentClass

Get instrument class (e.g. Cluster).

Returns:

Instrument class

Return type:

InstrumentClass

property instrument_type: InstrumentType

Get instrument type (e.g. MM, QRM, QCM).

Returns:

Instrument type

Return type:

InstrumentType

get_idn() → Dict

Get device identity and build information and convert them to a dictionary.

Returns:

Dictionary containing manufacturer, model, serial number and build information. The build information is subdivided into FPGA firmware, kernel module software, application software and driver software build information. Each of those consist of the version, build date, build Git hash and Git build dirty indication.

Return type:

dict

get_system_state() → SystemState

Get general system state and convert it to a SystemState.

Returns:

Tuple containing general system status and corresponding flags.

Return type:

SystemStatus

get_system_status() → SystemStatus

Get general system status and convert it to a SystemStatus.

Returns:

Tuple containing general system status and corresponding flags.

Return type:

SystemStatus

arm_sequencer(slot: int | None = None, sequencer: int | None = None) → None

Prepare the indexed sequencer to start by putting it in the armed state. If no sequencer index is given, all sequencers are armed. Any sequencer that was already running is stopped and rearmed. If an invalid sequencer index is given, an error is set in system error.

Parameters:

• slot (Optional[int]) – The slot index of the module being referred to.

• sequencer (Optional[int]) – Sequencer index.

Raises:

RuntimeError – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

start_sequencer(slot: int | None = None, sequencer: int | None = None) → None

Start the indexed sequencer, thereby putting it in the running state. If an invalid sequencer index is given or the indexed sequencer was not yet armed, an error is set in system error. If no sequencer index is given, all armed sequencers are started and any sequencer not in the armed state is ignored. However, if no sequencer index is given and no sequencers are armed, and error is set in system error.

Parameters:

• slot (Optional[int]) – The slot index of the module being referred to.

• sequencer (Optional[int]) – Sequencer index.

Raises:

RuntimeError – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

stop_sequencer(slot: int | None = None, sequencer: int | None = None) → None

Stop the indexed sequencer, thereby putting it in the stopped state. If an invalid sequencer index is given, an error is set in system error. If no sequencer index is given, all sequencers are stopped.

Parameters:

• slot (Optional[int]) – The slot index of the module being referred to.

• sequencer (Optional[int]) – Sequencer index.

Raises:

RuntimeError – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

clear_sequencer_flags(slot: int | None = None, sequencer: int | None = None) → None

Clear flags

Parameters:

• slot (Optional[int]) – The slot index of the module being referred to.

• sequencer (int) – Sequencer index.

get_sequencer_state(slot: int, sequencer: int, timeout: int = 0, timeout_poll_res: float = 0.02) → SequencerState

Get the sequencer state. If an invalid sequencer index is given, an error is set in system error. If the timeout is set to zero, the function returns the state immediately. If a positive non-zero timeout is set, the function blocks until the sequencer completes. If the sequencer hasn’t stopped before the timeout expires, a TimeoutError is thrown.

Parameters:

• slot (int) – The slot index of the module being referred to.

• sequencer (int) – Sequencer index.

• timeout (int) – Timeout in minutes.

• timeout_poll_res (float) – Timeout polling resolution in seconds.

Returns:

Tuple containing sequencer status and corresponding flags.

Return type:

SequencerState

Raises:

TimeoutError – Timeout

get_sequencer_status(slot: int, sequencer: int, timeout: int = 0, timeout_poll_res: float = 0.02) → SequencerStatus

Get the sequencer status. If an invalid sequencer index is given, an error is set in system error. If the timeout is set to zero, the function returns the state immediately. If a positive non-zero timeout is set, the function blocks until the sequencer completes. If the sequencer hasn’t stopped before the timeout expires, a TimeoutError is thrown.

Parameters:

• slot (int) – The slot index of the module being referred to.

• sequencer (int) – Sequencer index.

• timeout (int) – Timeout in minutes.

• timeout_poll_res (float) – Timeout polling resolution in seconds.

Returns:

Tuple containing sequencer status and corresponding flags.

Return type:

SequencerState

Raises:

TimeoutError – Timeout

get_waveforms(slot: int, sequencer: int) → Dict

Get all waveforms and weigths in the AWG waveform list of indexed sequencer. The returned dictionary is structured as follows:

• name: waveform name.

  • data: waveform samples in a range of 1.0 to -1.0.

  • index: waveform index used by the sequencer Q1ASM program to refer

    to the waveform.

Parameters:

• slot (int) – The slot index of the module being referred to.

• sequencer (int) – Sequencer index.

Returns:

Dictionary with waveforms.

Return type:

dict

get_weights(slot: int, sequencer: int) → Dict

Get all weigths in the acquisition weight lists of indexed sequencer. The returned dictionary is structured as follows:

-name : weight name.

• data: weight samples in a range of 1.0 to -1.0.

• index: weight index used by the sequencer Q1ASM program to refer

  to the weight.

Parameters:

• slot (int) – The slot index of the module being referred to.

• sequencer (int) – Sequencer index.

Returns:

Dictionary with weights.

Return type:

dict

Raises:

NotImplementedError – Functionality not available on this module.

get_acquisition_state(slot: int, sequencer: int, timeout: int = 0, timeout_poll_res: float = 0.02) → bool

Return acquisition binning completion state of the indexed sequencer. If an invalid sequencer is given, an error is set in system error. If the timeout is set to zero, the function returns the state immediately. If a positive non-zero timeout is set, the function blocks until the acquisition binning completes. If the acquisition hasn’t completed before the timeout expires, a TimeoutError is thrown. Note that when sequencer state checking is enabled, the sequencer state is checked using get_sequencer_state with the selected timeout period first and then the acquisition state is checked with the same timeout period. This means that the total timeout period is two times the set timeout period.

Parameters:

• slot (int) – The slot index of the module being referred to.

• sequencer (int) – Sequencer index.

• timeout (int) – Timeout in minutes.

• timeout_poll_res (float) – Timeout polling resolution in seconds.

• check_seq_state (bool) – Check if sequencer is done before checking acquisition state.

Returns:

Indicates the acquisition binning completion state (False = uncompleted, True = completed).

Return type:

bool

Raises:

• TimeoutError – Timeout

• NotImplementedError – Functionality not available on this module.

get_acquisition_status(slot: int, sequencer: int, timeout: int = 0, timeout_poll_res: float = 0.02) → bool

Return acquisition binning completion status of the indexed sequencer. If an invalid sequencer is given, an error is set in system error. If the timeout is set to zero, the function returns the status immediately. If a positive non-zero timeout is set, the function blocks until the acquisition binning completes. If the acquisition hasn’t completed before the timeout expires, a TimeoutError is thrown. Note that when sequencer state checking is enabled, the sequencer state is checked using get_sequencer_status with the selected timeout period first and then the acquisition status is checked with the same timeout period. This means that the total timeout period is two times the set timeout period.

Parameters:

• slot (int) – The slot index of the module being referred to.

• sequencer (int) – Sequencer index.

• timeout (int) – Timeout in minutes.

• timeout_poll_res (float) – Timeout polling resolution in seconds.

• check_seq_state (bool) – Check if sequencer is done before checking acquisition status.

Returns:

Indicates the acquisition binning completion status (False = uncompleted, True = completed).

Return type:

bool

Raises:

• TimeoutError – Timeout

• NotImplementedError – Functionality not available on this module.

delete_acquisition_data(slot: int, sequencer: int, name: str = '', all: bool = False) → None

Delete data from an acquisition specified by name in the acquisition list of indexed sequencer or delete data in all acquisitions if all is True.

Parameters:

• slot (int) – The slot index of the module being referred to.

• sequencer (int) – Sequencer index.

• name (str) – Weight name

Raises:

NotImplementedError – Functionality not available on this module.

store_scope_acquisition(slot: int, sequencer: int, name: str) → None

After an acquisition has completed, store the scope acquisition results in the acquisition specified by name of the indexed sequencers. If an invalid sequencer index is given an error is set in system error. To get access to the acquisition results, the sequencer will be stopped when calling this function.

Parameters:

• slot (int) – The slot index of the module being referred to.

• sequencer (int) – Sequencer index.

• name (str) – Acquisition name.

Raises:

NotImplementedError – Functionality not available on this module.

get_acquisitions(slot: int, sequencer: int) → Dict

Get all acquisitions in acquisition lists of indexed sequencer. The acquisition scope and bin data is normalized to a range of -1.0 to 1.0 taking both the bit widths of the processing path and average count into considaration. For the binned integration results, the integration length is not handled during normalization and therefore these values have to be divided by their respective integration lenghts. The returned dictionary is structured as follows:

• name: acquisition name

  • index: acquisition index used by the sequencer Q1ASM program to refer to the acquisition.

  • acquisition: acquisition dictionary

    • scope: Scope data

      • path0: input path 0

        • data: acquisition samples in a range of 1.0 to -1.0.

        • out-of-range: out-of-range indication for the entire acquisition (False = in-range, True = out-of-range).

        • avg_cnt: number of averages.

      • path1: input path 1

        • data: acquisition samples in a range of 1.0 to -1.0.

        • out-of-range: out-of-range indication for the entire acquisition (False = in-range, True = out-of-range).

        • avg_cnt: number of averages.

    • bins: bin data

      • integration: integration data

        • path_0: input path 0 integration result bin list

        • path_1: input path 1 integration result bin list

      • threshold: threshold result bin list

      • valid: list of valid indications per bin

      • avg_cnt: list of number of averages per bin

Parameters:

• slot (int) – The slot index of the module being referred to.

• sequencer (int) – Sequencer index.

Returns:

Dictionary with acquisitions.

Return type:

dict

Raises:

NotImplementedError – Functionality not available on this module.

delete_dummy_binned_acquisition_data(slot_idx: int, sequencer: int | None = None, acq_index_name: str | None = None)

Delete all dummy binned acquisition data for the dummy.

Parameters:

• slot_idx (int) – Slot of the hardware you want to set the data to on a cluster.

• sequencer (Optional[int]) – Sequencer.

• acq_index_name (Optional[str]) – Acquisition index name.

set_dummy_binned_acquisition_data(slot_idx: int, sequencer: int, acq_index_name: str, data: Iterable[DummyBinnedAcquisitionData | None])

Set dummy binned acquisition data for the dummy.

Parameters:

• slot_idx (int) – Slot of the hardware you want to set the data to on a cluster.

• sequencer (int) – Sequencer.

• acq_index_name (str) – Acquisition index name.

• data (Iterable[Union[DummyBinnedAcquisitionData, None]]) – Dummy data for the binned acquisition. An iterable of all the bin values.

delete_dummy_scope_acquisition_data(slot_idx: int, sequencer: int | None)

Delete dummy scope acquisition data for the dummy.

Parameters:

• slot_idx (int) – Slot of the hardware you want to set the data to on a cluster.

• sequencer (Union[int, None]) – Sequencer.

set_dummy_scope_acquisition_data(slot_idx: int, sequencer: int | None, data: DummyScopeAcquisitionData)

Set dummy scope acquisition data for the dummy.

Parameters:

• slot_idx (int) – Slot of the hardware you want to set the data to on a cluster.

• sequencer (Union[int, None]) – Sequencer.

• data (DummyScopeAcquisitionData) – Dummy data for the scope acquisition.

SCPI interface

class qblox_instruments.scpi.Cluster(transport: Transport, debug: int = 0)

Bases: Ieee488_2

This interface provides an API for the mandatory and required SCPI calls and adds Cluster related functionality (see SCPI).

__init__(transport: Transport, debug: int = 0)

Creates SCPI interface object.

Parameters:

• transport (Transport) – Transport class responsible for the lowest level of communication (e.g. Ethernet).

• debug (int) – Debug level (0 = normal, 1 = no version check, >1 = no version or error checking).

Raises:

ConnectionError – Debug level is 0 and there is a device or version mismatch.

get_system_error() → str

Get system error from queue (see SCPI).

Parameters:

None –

Returns:

System error description string.

Return type:

str

get_num_system_error() → int

Get number of system errors (see SCPI).

Parameters:

None –

Returns:

Current number of system errors.

Return type:

int

get_system_version() → str

Get SCPI system version (see SCPI).

Parameters:

None –

Returns:

SCPI system version.

Return type:

str

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

set_name(name: str) → None

Sets the customer-specified name of the instrument. The name must not contain any newlines, backslashes, or double quotes.

Parameters:

name (str) – The new name for the device.

Return type:

None

Raises:

• Exception – Invalid input parameter type.

• Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_name() → str

Returns the customer-specified name of the instrument.

Parameters:

None –

Returns:

The name of the device.

Return type:

str

Raises:

• Exception – Invalid input parameter type.

• Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

set_ip_config(config: str) → None

Reconfigures the IP address of this device. The configuration will not go into effect until reboot() is called or the device is power-cycled.

Parameters:

config (str) –

IP configuration. May be one of the following things:

• an IPv4 address including prefix length, for example 192.168.0.2/24, - the string dhcp to enable IPv4 DHCP, - an IPv6 address including prefix length, for example 1:2::3:4/64, or - a semicolon-separated combination of an IPv4 configuration (IP address or dhcp) and an IPv6 address.

Return type:

None

Raises:

• Exception – Invalid input parameter type.

• Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_ip_config() → str

Returns the IP address configuration that will go into effect when the device reboots.

Parameters:

None –

Returns:

IP configuration. Can be one of the following things:

• an IPv4 address including prefix length, for example 192.168.0.2/24, - the string dhcp to enable IPv4 DHCP, - an IPv6 address including prefix length, for example 1:2::3:4/64, or - a semicolon-separated combination of an IPv4 configuration (IP address or dhcp) and an IPv6 address.

Return type:

str

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

reboot() → None

Reboots the instrument.

Parameters:

None –

Return type:

None

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

clear() → None

Clear all status and event registers (see SCPI).

Parameters:

None –

Return type:

None

Raises:

• Exception – Invalid input parameter type.

• Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_status_byte() → int

Get status byte register. Register is only cleared when feeding registers are cleared (see SCPI).

Parameters:

None –

Returns:

Status byte register.

Return type:

int

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

set_service_request_enable(reg: int) → None

Set service request enable register (see SCPI).

Parameters:

reg (int) – Service request enable register.

Return type:

None

Raises:

• Exception – Invalid input parameter type.

• Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_service_request_enable() → int

Get service request enable register. The register is cleared after reading it (see SCPI).

Parameters:

None –

Returns:

Service request enable register.

Return type:

int

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

set_standard_event_status_enable(reg: int) → None

Set standard event status enable register (see SCPI).

Parameters:

reg (int) – Standard event status enable register.

Return type:

None

Raises:

• Exception – Invalid input parameter type.

• Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_standard_event_status_enable() → int

Get standard event status enable register. The register is cleared after reading it (see SCPI).

Parameters:

None –

Returns:

Standard event status enable register.

Return type:

int

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_standard_event_status() → int

Get standard event status register. The register is cleared after reading it (see SCPI).

Parameters:

None –

Returns:

Standard event status register.

Return type:

int

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

set_operation_complete() → None

Set device in operation complete query active state (see SCPI).

Parameters:

None –

Return type:

None

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_operation_complete() → bool

Get operation complete state (see SCPI).

Parameters:

None –

Returns:

Operation complete state (False = running, True = completed).

Return type:

bool

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

test() → bool

Run self-test. Currently not implemented (see SCPI).

Parameters:

None –

Returns:

Test result (False = failed, True = success).

Return type:

bool

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

wait() → None

Wait until operations completed before continuing (see SCPI).

Parameters:

None –

Return type:

None

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

preset_system_status() → None

Preset system status registers. Connects general system status flags for PLL unlock and temperature out-of-range indications to event status enable, status questionable temperature and status questionable frequency registers respectively (see SCPI).

Parameters:

None –

Return type:

None

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_questionable_condition() → int

Get status questionable condition register (see SCPI).

Parameters:

None –

Returns:

Status questionable condition register.

Return type:

int

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_questionable_event() → int

Get status questionable event register (see SCPI).

Parameters:

None –

Returns:

Status questionable event register.

Return type:

int

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

set_questionable_enable(reg: int) → None

Set status questionable enable register (see SCPI).

Parameters:

reg (int) – Status questionable enable register.

Return type:

None

Raises:

• Exception – Invalid input parameter type.

• Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_questionable_enable() → int

Get status questionable enable register (see SCPI).

Parameters:

None –

Returns:

Status questionable enable register.

Return type:

int

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_operation_condition() → int

Get status operation condition register (see SCPI).

Parameters:

None –

Returns:

Status operation condition register.

Return type:

int

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_operation_events() → int

Get status operation event register (see SCPI).

Parameters:

None –

Returns:

Status operation event register.

Return type:

int

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

set_operation_enable(reg: int) → None

Set status operation enable register (see SCPI).

Parameters:

reg (int) – Status operation enable register.

Return type:

None

Raises:

• Exception – Invalid input parameter type.

• Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_operation_enable() → int

Get status operation enable register (see SCPI).

Parameters:

None –

Returns:

Status operation enable register.

Return type:

int

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

identify() → None

Toggle frontpanel LEDs to visually identify the instrument.

Parameters:

None –

Return type:

None

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_current_fpga_temperature(slot: int) → float

Get current FPGA junction temperature (inside device).

Parameters:

slot (int) – slot index.

Returns:

Current FPGA junction temperature.

Return type:

float

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_maximum_fpga_temperature(slot: int) → float

Get maximum FPGA junction temperature since boot or clear (inside device).

Parameters:

slot (int) – slot index.

Returns:

Maximum FPGA junction temperature.

Return type:

float

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_current_carrier_temperature(slot: int) → float

Get current carrier board temperature (inside device).

Parameters:

slot (int) – slot index.

Returns:

Current carrier board temperature.

Return type:

float

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_maximum_carrier_temperature(slot: int) → float

Get maximum carrier board temperature since boot or clear (inside device).

Parameters:

slot (int) – slot index.

Returns:

Maximum carrier board temperature.

Return type:

float

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_current_bp_temperature_0() → float

Get current backplane board temperature from sensor 0 (inside device).

Parameters:

None –

Returns:

Current backplane board temperature from sensor 0.

Return type:

float

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_maximum_bp_temperature_0() → float

Get maximum backplane board temperature from sensor 0 since boot or clear (inside device).

Parameters:

None –

Returns:

Maximum backplane board temperature from sensor 0.

Return type:

float

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_current_bp_temperature_1() → float

Get current backplane board temperature from sensor 1 (inside device).

Parameters:

None –

Returns:

Current backplane board temperature from sensor 1.

Return type:

float

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_maximum_bp_temperature_1() → float

Get maximum backplane board temperature from sensor 1 since boot or clear (inside device).

Parameters:

None –

Returns:

Maximum backplane board temperature from sensor 1.

Return type:

float

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_current_bp_temperature_2() → float

Get current backplane board temperature from sensor 2 (inside device).

Parameters:

None –

Returns:

Current backplane board temperature from sensor 2.

Return type:

float

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_maximum_bp_temperature_2() → float

Get maximum backplane board temperature from sensor 2 since boot or clear (inside device).

Parameters:

None –

Returns:

Maximum backplane board temperature from sensor 2.

Return type:

float

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

set_trg_in_delay(trg_in_delay: int) → None

Set external trigger input delay

Parameters:

trg_in_delay (int) – External trigger input delay (ps), in steps of 39 ps.

Return type:

None

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_trg_in_delay() → int

Get external trigger input delay

Parameters:

None –

Returns:

Current status of the external trigger input delay (ps), in steps of 39 ps.

Return type:

int

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

set_trg_in_map_en(trg_in_map_en: bool) → None

Set external trigger input map enable

Parameters:

trg_in_map_en (bool) – External trigger input map enable

Return type:

None

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_trg_in_map_en() → bool

Get external trigger input map enable

Parameters:

None –

Returns:

Current status of the external trigger input map enable

Return type:

bool

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

set_trg_in_map_addr(trg_in_map_addr: int) → None

Set external trigger input map enable

Parameters:

trg_in_map_addr (int) – External trigger input map address

Return type:

None

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_trg_in_map_addr() → int

Get external trigger input map address

Parameters:

None –

Returns:

Current status of the external trigger input map address

Return type:

int

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

reset_trigger_monitor_count(address: int) → None

Reset external trigger monitor counter

Parameters:

address (int) – Address of the trigger which count has to be reset

Return type:

None

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_trigger_monitor_count(address: int) → int

Get trigger monitor count

Parameters:

address (int) – Address of the trigger

Returns:

Current status of trigger monitor counter

Return type:

int

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_trigger_monitor_latest() → int

Get trigger monitor latest value

Parameters:

None –

Returns:

Latest value from the trigger monitor counter

Return type:

int

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_assembler_status(slot: int) → bool

Get assembler status. Refer to the assembler log to get more information regarding the assembler result.

Parameters:

slot (int) – slot index.

Returns:

Assembler status (False = failed, True = success).

Return type:

bool

Raises:

• Exception – Invalid input parameter type.

• Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_assembler_log(slot: int) → str

Get assembler log.

Parameters:

slot (int) – slot index.

Returns:

Assembler log.

Return type:

str

Raises:

• Exception – Invalid input parameter type.

• Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_current_afe_temperature(slot: int) → float

Get current AFE temperature.

Parameters:

slot (int) – slot index.

Returns:

current

Return type:

float

Raises:

• Exception – Invalid input parameter type.

• Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_maximum_afe_temperature(slot: int) → float

Get maximum AFE temperature.

Parameters:

slot (int) – slot index.

Returns:

maximum

Return type:

float

Raises:

• Exception – Invalid input parameter type.

• Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_current_lo_temperature(slot: int) → float

Get current LO temperature.

Parameters:

slot (int) – slot index.

Returns:

current

Return type:

float

Raises:

• Exception – Invalid input parameter type.

• Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_maximum_lo_temperature(slot: int) → float

Get maximum LO temperature.

Parameters:

slot (int) – slot index.

Returns:

maximum

Return type:

float

Raises:

• Exception – Invalid input parameter type.

• Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

start_adc_calib(slot: int) → None

Calibrates ADC delay and offset values. This method sets the correct delay values for every input data index (IO data lane) in order to avoid timing violations which occur while sampling ADC data. It also calibrates offsets internal to the ADC.

Parameters:

slot (int) – slot index.

Return type:

None

Raises:

• Exception – Invalid input parameter type.

• Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

Supporting classes and functions

Please have a look at:

• QCM-QRM API

• Sequencer API

• Generic native interface functions

• IEEE488.2

• Instrument types