Cluster API

The Cluster driver is separated into three layers:

QCoDeS driver: Instrument driver based on QCoDeS and the instrument’s native interface.
Native interface: Instrument API that provides control over the instrument and is an extension of the the SCPI interface.
SCPI interface: Instrument API based on the SCPI standard which in turn is based on IEEE488.2.

Warning

This is a preliminary driver for the Cluster that is currently under development.

QCoDeS driver

class qblox_instruments.Cluster(*args: Any, **kwargs: Any)[source]

Bases: Cluster, Instrument

This class connects QCoDeS to the Cluster native interface.

__init__(name: str, identifier: str | None = None, port: int | None = None, debug: int | None = None, dummy_cfg: Dict | None = None)[source]

Creates Cluster QCoDeS class and adds all relevant instrument parameters. These instrument parameters call the associated methods provided by the native interface.

Parameters:

name (str) – Instrument name.
identifier (Optional[str]) – Instrument identifier. See resolve(). If None, the instrument is identified by name.
port (Optional[int]) – Override for the TCP port through which we should connect.
debug (Optional[int]) – Debug level (0 | None = normal, 1 = no version check, >1 = no version or error checking).
dummy_cfg (Optional[Dict]) – Configure as dummy using this configuration. For each slot that needs to be occupied by a module add the slot index as key and specify the type of module in the slot using the type ClusterType.

property modules: List

Get list of modules.

Returns:: List of modules.
Return type:: list

reset() → None[source]: Resets device, invalidates QCoDeS parameter cache and clears all status and event registers (see SCPI).

disconnect_outputs(slot: int) → None[source]

Disconnects all outputs from the waveform generator paths of the sequencers.

Parameters:: slot (int) – Slot index

disconnect_inputs(slot: int) → None[source]

Disconnects all inputs from the acquisition paths of the sequencers.

Parameters:: slot (int) – Slot index

connect_sequencer(slot: int, sequencer: int, *connections: str) → None[source]

Makes new connections between the indexed sequencer and some inputs and/or outputs. This will fail if a requested connection already existed, or if the connection could not be made due to a conflict with an existing connection (hardware constraints). In such a case, the channel map will not be affected.

Parameters:

slot (int) – Slot index
sequencer (int) – Sequencer index
*connections (str) – Zero or more connections to make, each specified using a string. The string should have the format <direction><channel> or <direction><I-channel>_<Q-channel>. <direction> must be in to make a connection between an input and the acquisition path, out to make a connection from the waveform generator to an output, or io to do both. The channels must be integer channel indices. If only one channel is specified, the sequencer operates in real mode; if two channels are specified, it operates in complex mode.

Raises:

RuntimeError – If the connection command could not be completed due to a conflict.
ValueError – If parsing of a connection fails.

QCoDeS instrument parameters

QCoDeS parameters generated by Cluster.

Cluster.IDN()

Please see QCoDeS for a description.

Properties:

value: Anything

Cluster.led_brightness()

Sets/gets frontpanel LED brightness.

Properties:

value: Enum: {‘low’, ‘medium’, ‘high’, ‘off’}

Cluster.reference_source()

Sets/gets reference source (‘internal’ = internal 10 MHz, ‘external’ = external 10 MHz).

Properties:

value: Enum: {‘external’, ‘internal’}

Cluster.ext_trigger_input_delay()

Sets/gets the trigger address to which the external inputtrigger is mapped to the trigger network (T1 to T15).

Properties:

unit: ps
value: Ints 0<=v<=1209, Multiples of 39

Cluster.ext_trigger_input_trigger_en()

Enable/disable the external input trigger.

Properties:

value: Boolean

Cluster.ext_trigger_input_trigger_address()

Sets/gets the external input trigger address to which the input trigger is mapped to the trigger network (T1 to T15).

Properties:

value: Numbers 1<=v<=15

Cluster.trigger1_monitor_count()

Gets the trigger monitor count from trigger address T1.

Properties:

value: on

Cluster.trigger2_monitor_count()

Gets the trigger monitor count from trigger address T2.

Properties:

value: on

Cluster.trigger3_monitor_count()

Gets the trigger monitor count from trigger address T3.

Properties:

value: on

Cluster.trigger4_monitor_count()

Gets the trigger monitor count from trigger address T4.

Properties:

value: on

Cluster.trigger5_monitor_count()

Gets the trigger monitor count from trigger address T5.

Properties:

value: on

Cluster.trigger6_monitor_count()

Gets the trigger monitor count from trigger address T6.

Properties:

value: on

Cluster.trigger7_monitor_count()

Gets the trigger monitor count from trigger address T7.

Properties:

value: on

Cluster.trigger8_monitor_count()

Gets the trigger monitor count from trigger address T8.

Properties:

value: on

Cluster.trigger9_monitor_count()

Gets the trigger monitor count from trigger address T9.

Properties:

value: on

Cluster.trigger10_monitor_count()

Gets the trigger monitor count from trigger address T10.

Properties:

value: on

Cluster.trigger11_monitor_count()

Gets the trigger monitor count from trigger address T11.

Properties:

value: on

Cluster.trigger12_monitor_count()

Gets the trigger monitor count from trigger address T12.

Properties:

value: on

Cluster.trigger13_monitor_count()

Gets the trigger monitor count from trigger address T13.

Properties:

value: on

Cluster.trigger14_monitor_count()

Gets the trigger monitor count from trigger address T14.

Properties:

value: on

Cluster.trigger15_monitor_count()

Gets the trigger monitor count from trigger address T15.

Properties:

value: on

Cluster.trigger_monitor_latest()

Gets the trigger address which was triggered last (T1 to T15).

Properties:

value: on

QCoDeS module parameters

Besides instrument parameters, the Cluster also has parameters for each module in the Cluster which are described in QCM-QRM API.

Native interface

class qblox_instruments.native.Cluster(identifier: str, port: int | None = None, debug: int | None = None, dummy_cfg: Dict | None = None)[source]

Bases: Cluster

Class that provides the native API for the Cluster. It provides methods to control all functions and features provided by the Cluster.

Note that the bulk of the functionality of this class is contained in the generic_func module so that this functionality can be shared between instruments.

__init__(identifier: str, port: int | None = None, debug: int | None = None, dummy_cfg: Dict | None = None)[source]

Creates Cluster native interface object.

Parameters:

identifier (str) – Instrument identifier. See resolve() for more information.
port (Optional[int]) – Instrument port. If None, this will be determined automatically.
debug (Optional[int]) – Debug level (0 | None = normal, 1 = no version check, >1 = no version or error checking).
dummy_cfg (Optional[Dict]) – Configure as dummy using this configuration. For each slot that needs to be occupied by a module add the slot index as key and specify the type of module in the slot using the type ClusterType.

Raises:

RuntimeError – Instrument cannot be reached due to invalid IP configuration.
ConnectionError – Instrument type is not supported.

property instrument_class: InstrumentClass

Get instrument class (e.g. Pulsar, Cluster).

Returns:: Instrument class
Return type:: InstrumentClass

property instrument_type: InstrumentType

Get instrument type (e.g. MM, QRM, QCM).

Returns:: Instrument type
Return type:: InstrumentType

get_idn() → Dict[source]

Get device identity and build information and convert them to a dictionary.

Returns:: Dictionary containing manufacturer, model, serial number and build information. The build information is subdivided into FPGA firmware, kernel module software, application software and driver software build information. Each of those consist of the version, build date, build Git hash and Git build dirty indication.
Return type:: dict

get_system_state() → SystemState[source]

Get general system state and convert it to a SystemState.

Returns:: Tuple containing general system status and corresponding flags.
Return type:: SystemStatus

arm_sequencer(slot: int | None = None, sequencer: int | None = None) → None[source]

Prepare the indexed sequencer to start by putting it in the armed state. If no sequencer index is given, all sequencers are armed. Any sequencer that was already running is stopped and rearmed. If an invalid sequencer index is given, an error is set in system error.

Parameters:: sequencer (Optional[int]) – Sequencer index.
Raises:: RuntimeError – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

start_sequencer(slot: int | None = None, sequencer: int | None = None) → None[source]

Start the indexed sequencer, thereby putting it in the running state. If an invalid sequencer index is given or the indexed sequencer was not yet armed, an error is set in system error. If no sequencer index is given, all armed sequencers are started and any sequencer not in the armed state is ignored. However, if no sequencer index is given and no sequencers are armed, and error is set in system error.

Parameters:: sequencer (Optional[int]) – Sequencer index.
Raises:: RuntimeError – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

stop_sequencer(slot: int | None = None, sequencer: int | None = None) → None[source]

Stop the indexed sequencer, thereby putting it in the stopped state. If an invalid sequencer index is given, an error is set in system error. If no sequencer index is given, all sequencers are stopped.

Parameters:: sequencer (Optional[int]) – Sequencer index.
Raises:: RuntimeError – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_sequencer_state(slot: int, sequencer: int, timeout: int = 0, timeout_poll_res: float = 0.02) → SequencerState[source]

Get the sequencer state. If an invalid sequencer index is given, an error is set in system error. If the timeout is set to zero, the function returns the state immediately. If a positive non-zero timeout is set, the function blocks until the sequencer completes. If the sequencer hasn’t stopped before the timeout expires, a TimeoutError is thrown.

Parameters:

sequencer (int) – Sequencer index.
timeout (int) – Timeout in minutes.
timeout_poll_res (float) – Timeout polling resolution in seconds.

Returns:

Tuple containing sequencer status and corresponding flags.

Return type:

SequencerState

Raises:

TimeoutError – Timeout

get_waveforms(slot: int, sequencer: int) → Dict[source]

Get all waveforms and weigths in the AWG waveform list of indexed sequencer. The returned dictionary is structured as follows:

name: waveform name.
- data: waveform samples in a range of 1.0 to -1.0.
- index: waveform index used by the sequencer Q1ASM program to refer
  to the waveform.

Parameters:: sequencer (int) – Sequencer index.
Returns:: Dictionary with waveforms.
Return type:: dict

get_weights(slot: int, sequencer: int) → Dict[source]

Get all weigths in the acquisition weight lists of indexed sequencer. The returned dictionary is structured as follows:

-name : weight name.

data: weight samples in a range of 1.0 to -1.0.

index: weight index used by the sequencer Q1ASM program to refer
to the weight.

Parameters:: sequencer (int) – Sequencer index.
Returns:: Dictionary with weights.
Return type:: dict
Raises:: NotImplementedError – Functionality not available on this module.

get_acquisition_state(slot: int, sequencer: int, timeout: int = 0, timeout_poll_res: float = 0.02) → bool[source]

Return acquisition binning completion state of the indexed sequencer. If an invalid sequencer is given, an error is set in system error. If the timeout is set to zero, the function returns the state immediately. If a positive non-zero timeout is set, the function blocks until the acquisition binning completes. If the acquisition hasn’t completed before the timeout expires, a TimeoutError is thrown. Note that when sequencer state checking is enabled, the sequencer state is checked using get_sequencer_state with the selected timeout period first and then the acquisition state is checked with the same timeout period. This means that the total timeout period is two times the set timeout period.

Parameters:

sequencer (int) – Sequencer index.
timeout (int) – Timeout in minutes.
timeout_poll_res (float) – Timeout polling resolution in seconds.
check_seq_state (bool) – Check if sequencer is done before checking acquisition state.

Returns:

Indicates the acquisition binning completion state (False = uncompleted, True = completed).

Return type:

bool

Raises:

TimeoutError – Timeout
NotImplementedError – Functionality not available on this module.

delete_acquisition_data(slot: int, sequencer: int, name: str = '', all: bool = False) → None[source]

Delete data from an acquisition specified by name in the acquisition list of indexed sequencer or delete data in all acquisitions if all is True.

Parameters:

sequencer (int) – Sequencer index.
name (str) – Weight name

Raises:

NotImplementedError – Functionality not available on this module.

store_scope_acquisition(slot: int, sequencer: int, name: str) → None[source]

After an acquisition has completed, store the scope acquisition results in the acquisition specified by name of the indexed sequencers. If an invalid sequencer index is given an error is set in system error. To get access to the acquisition results, the sequencer will be stopped when calling this function.

Parameters:

sequencer (int) – Sequencer index.
name (str) – Acquisition name.

Raises:

NotImplementedError – Functionality not available on this module.

get_acquisitions(slot: int, sequencer: int) → Dict[source]

Get all acquisitions in acquisition lists of indexed sequencer. The acquisition scope and bin data is normalized to a range of -1.0 to 1.0 taking both the bit widths of the processing path and average count into considaration. For the binned integration results, the integration length is not handled during normalization and therefore these values have to be divided by their respective integration lenghts. The returned dictionary is structured as follows:

name: acquisition name
- index: acquisition index used by the sequencer Q1ASM program to refer to the acquisition.
- acquisition: acquisition dictionary
  scope: Scope data
  
  path0: input path 0
  
  data: acquisition samples in a range of 1.0 to -1.0.
  
  out-of-range: out-of-range indication for the entire acquisition (False = in-range, True = out-of-range).
  
  avg_cnt: number of averages.
  
  path1: input path 1
  
  data: acquisition samples in a range of 1.0 to -1.0.
  
  out-of-range: out-of-range indication for the entire acquisition (False = in-range, True = out-of-range).
  
  avg_cnt: number of averages.
  
  bins: bin data
  
  integration: integration data
  
  path_0: input path 0 integration result bin list
  
  path_1: input path 1 integration result bin list
  
  threshold: threshold result bin list
  
  valid: list of valid indications per bin
  
  avg_cnt: list of number of averages per bin

Parameters:: sequencer (int) – Sequencer index.
Returns:: Dictionary with acquisitions.
Return type:: dict
Raises:: NotImplementedError – Functionality not available on this module.

delete_dummy_binned_acquisition_data(slot_idx: int, sequencer: int | None = None, acq_index_name: str | None = None)[source]

Delete all dummy binned acquisition data for the dummy.

Parameters:

slot_idx (int) – Slot of the hardware you want to set the data to on a cluster.
sequencer (Optional[int]) – Sequencer.
acq_index_name (Optional[str]) – Acquisition index name.

set_dummy_binned_acquisition_data(slot_idx: int, sequencer: int, acq_index_name: str, data: Iterable[DummyBinnedAcquisitionData | None])[source]

Set dummy binned acquisition data for the dummy.

Parameters:

slot_idx (int) – Slot of the hardware you want to set the data to on a cluster.
sequencer (int) – Sequencer.
acq_index_name (str) – Acquisition index name.
data (Iterable[Union[DummyBinnedAcquisitionData, None]]) – Dummy data for the binned acquisition. An iterable of all the bin values.

delete_dummy_scope_acquisition_data(slot_idx: int, sequencer: int | None)[source]

Delete dummy scope acquisition data for the dummy.

Parameters:

slot_idx (int) – Slot of the hardware you want to set the data to on a cluster.
sequencer (Union[int, None]) – Sequencer.

set_dummy_scope_acquisition_data(slot_idx: int, sequencer: int | None, data: DummyScopeAcquisitionData)[source]

Set dummy scope acquisition data for the dummy.

Parameters:

slot_idx (int) – Slot of the hardware you want to set the data to on a cluster.
sequencer (Union[int, None]) – Sequencer.
data (DummyScopeAcquisitionData) – Dummy data for the scope acquisition.

SCPI interface

class qblox_instruments.scpi.Cluster(transport: Transport, debug: int = 0)[source]

Bases: Ieee488_2

This interface provides an API for the mandatory and required SCPI calls and adds Pulsar related functionality (see SCPI).

__init__(transport: Transport, debug: int = 0)[source]

Creates SCPI interface object.

Parameters:

transport (Transport) – Transport class responsible for the lowest level of communication (e.g. Ethernet).
debug (int) – Debug level (0 = normal, 1 = no version check, >1 = no version or error checking).

Raises:

ConnectionError – Debug level is 0 and there is a device or version mismatch.

get_system_error() → str[source]

Get system error from queue (see SCPI).

Parameters:: None –
Returns:: System error description string.
Return type:: str

get_num_system_error() → int[source]

Get number of system errors (see SCPI).

Parameters:: None –
Returns:: Current number of system errors.
Return type:: int

get_system_version() → str[source]

Get SCPI system version (see SCPI).

Parameters:: None –
Returns:: SCPI system version.
Return type:: str
Raises:: Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

set_name(name: str) → None[source]

Sets the customer-specified name of the instrument. The name must not contain any newlines, backslashes, or double quotes.

Parameters:

name (str) – The new name for the device.

Return type:

None

Raises:

Exception – Invalid input parameter type.
Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_name() → str[source]

Returns the customer-specified name of the instrument.

Parameters:

None –

Returns:

The name of the device.

Return type:

str

Raises:

Exception – Invalid input parameter type.
Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

set_ip_config(config: str) → None[source]

Reconfigures the IP address of this device. The configuration will not go into effect until reboot() is called or the device is power-cycled.

Parameters:

config (str) –

IP configuration. May be one of the following things:

an IPv4 address including prefix length, for example 192.168.0.2/24, - the string dhcp to enable IPv4 DHCP, - an IPv6 address including prefix length, for example 1:2::3:4/64, or - a semicolon-separated combination of an IPv4 configuration (IP address or dhcp) and an IPv6 address.

Return type:

None

Raises:

Exception – Invalid input parameter type.
Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_ip_config() → str[source]

Returns the IP address configuration that will go into effect when the device reboots.

Parameters:

None –

Returns:

IP configuration. Can be one of the following things:

an IPv4 address including prefix length, for example 192.168.0.2/24, - the string dhcp to enable IPv4 DHCP, - an IPv6 address including prefix length, for example 1:2::3:4/64, or - a semicolon-separated combination of an IPv4 configuration (IP address or dhcp) and an IPv6 address.

Return type:

str

Raises:

Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

reboot() → None[source]

Reboots the instrument.

Parameters:: None –
Return type:: None
Raises:: Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

clear() → None[source]

Clear all status and event registers (see SCPI).

Parameters:

None –

Return type:

None

Raises:

Exception – Invalid input parameter type.
Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_status_byte() → int[source]

Get status byte register. Register is only cleared when feeding registers are cleared (see SCPI).

Parameters:: None –
Returns:: Status byte register.
Return type:: int
Raises:: Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

set_service_request_enable(reg: int) → None[source]

Set service request enable register (see SCPI).

Parameters:

reg (int) – Service request enable register.

Return type:

None

Raises:

Exception – Invalid input parameter type.
Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_service_request_enable() → int[source]

Get service request enable register. The register is cleared after reading it (see SCPI).

Parameters:: None –
Returns:: Service request enable register.
Return type:: int
Raises:: Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

set_standard_event_status_enable(reg: int) → None[source]

Set standard event status enable register (see SCPI).

Parameters:

reg (int) – Standard event status enable register.

Return type:

None

Raises:

Exception – Invalid input parameter type.
Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_standard_event_status_enable() → int[source]

Get standard event status enable register. The register is cleared after reading it (see SCPI).

Parameters:: None –
Returns:: Standard event status enable register.
Return type:: int
Raises:: Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_standard_event_status() → int[source]

Get standard event status register. The register is cleared after reading it (see SCPI).

Parameters:: None –
Returns:: Standard event status register.
Return type:: int
Raises:: Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

set_operation_complete() → None[source]

Set device in operation complete query active state (see SCPI).

Parameters:: None –
Return type:: None
Raises:: Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_operation_complete() → bool[source]

Get operation complete state (see SCPI).

Parameters:: None –
Returns:: Operation complete state (False = running, True = completed).
Return type:: bool
Raises:: Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

test() → bool[source]

Run self-test. Currently not implemented (see SCPI).

Parameters:: None –
Returns:: Test result (False = failed, True = success).
Return type:: bool
Raises:: Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

wait() → None[source]

Wait until operations completed before continuing (see SCPI).

Parameters:: None –
Return type:: None
Raises:: Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

preset_system_status() → None[source]

Preset system status registers. Connects general system status flags for PLL unlock and temperature out-of-range indications to event status enable, status questionable temperature and status questionable frequency registers respectively (see SCPI).

Parameters:: None –
Return type:: None
Raises:: Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_questionable_condition() → int[source]

Get status questionable condition register (see SCPI).

Parameters:: None –
Returns:: Status questionable condition register.
Return type:: int
Raises:: Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_questionable_event() → int[source]

Get status questionable event register (see SCPI).

Parameters:: None –
Returns:: Status questionable event register.
Return type:: int
Raises:: Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

set_questionable_enable(reg: int) → None[source]

Set status questionable enable register (see SCPI).

Parameters:

reg (int) – Status questionable enable register.

Return type:

None

Raises:

Exception – Invalid input parameter type.
Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_questionable_enable() → int[source]

Get status questionable enable register (see SCPI).

Parameters:: None –
Returns:: Status questionable enable register.
Return type:: int
Raises:: Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_operation_condition() → int[source]

Get status operation condition register (see SCPI).

Parameters:: None –
Returns:: Status operation condition register.
Return type:: int
Raises:: Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_operation_events() → int[source]

Get status operation event register (see SCPI).

Parameters:: None –
Returns:: Status operation event register.
Return type:: int
Raises:: Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

set_operation_enable(reg: int) → None[source]

Set status operation enable register (see SCPI).

Parameters:

reg (int) – Status operation enable register.

Return type:

None

Raises:

Exception – Invalid input parameter type.
Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_operation_enable() → int[source]

Get status operation enable register (see SCPI).

Parameters:: None –
Returns:: Status operation enable register.
Return type:: int
Raises:: Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

identify() → None[source]

Toggle frontpanel LEDs to visually identify the instrument.

Parameters:: None –
Return type:: None
Raises:: Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_current_fpga_temperature(slot: int) → float[source]

Get current FPGA junction temperature (inside device).

Parameters:: slot (int) – slot index.
Returns:: Current FPGA junction temperature.
Return type:: float
Raises:: Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_maximum_fpga_temperature(slot: int) → float[source]

Get maximum FPGA junction temperature since boot or clear (inside device).

Parameters:: slot (int) – slot index.
Returns:: Maximum FPGA junction temperature.
Return type:: float
Raises:: Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_current_carrier_temperature(slot: int) → float[source]

Get current carrier board temperature (inside device).

Parameters:: slot (int) – slot index.
Returns:: Current carrier board temperature.
Return type:: float
Raises:: Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_maximum_carrier_temperature(slot: int) → float[source]

Get maximum carrier board temperature since boot or clear (inside device).

Parameters:: slot (int) – slot index.
Returns:: Maximum carrier board temperature.
Return type:: float
Raises:: Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_current_bp_temperature_0() → float[source]

Get current backplane board temperature from sensor 0 (inside device).

Parameters:: None –
Returns:: Current backplane board temperature from sensor 0.
Return type:: float
Raises:: Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_maximum_bp_temperature_0() → float[source]

Get maximum backplane board temperature from sensor 0 since boot or clear (inside device).

Parameters:: None –
Returns:: Maximum backplane board temperature from sensor 0.
Return type:: float
Raises:: Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_current_bp_temperature_1() → float[source]

Get current backplane board temperature from sensor 1 (inside device).

Parameters:: None –
Returns:: Current backplane board temperature from sensor 1.
Return type:: float
Raises:: Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_maximum_bp_temperature_1() → float[source]

Get maximum backplane board temperature from sensor 1 since boot or clear (inside device).

Parameters:: None –
Returns:: Maximum backplane board temperature from sensor 1.
Return type:: float
Raises:: Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_current_bp_temperature_2() → float[source]

Get current backplane board temperature from sensor 2 (inside device).

Parameters:: None –
Returns:: Current backplane board temperature from sensor 2.
Return type:: float
Raises:: Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_maximum_bp_temperature_2() → float[source]

Get maximum backplane board temperature from sensor 2 since boot or clear (inside device).

Parameters:: None –
Returns:: Maximum backplane board temperature from sensor 2.
Return type:: float
Raises:: Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

set_trg_in_delay(trg_in_delay: int) → None[source]

Set external trigger input delay

Parameters:: trg_in_delay (int) – External trigger input delay (ps), in steps of 39 ps.
Return type:: None
Raises:: Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_trg_in_delay() → int[source]

Get external trigger input delay

Parameters:: None –
Returns:: Current status of the external trigger input delay (ps), in steps of 39 ps.
Return type:: int
Raises:: Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

set_trg_in_map_en(trg_in_map_en: bool) → None[source]

Set external trigger input map enable

Parameters:: trg_in_map_en (bool) – External trigger input map enable
Return type:: None
Raises:: Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_trg_in_map_en() → bool[source]

Get external trigger input map enable

Parameters:: None –
Returns:: Current status of the external trigger input map enable
Return type:: bool
Raises:: Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

set_trg_in_map_addr(trg_in_map_addr: int) → None[source]

Set external trigger input map enable

Parameters:: trg_in_map_addr (int) – External trigger input map address
Return type:: None
Raises:: Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_trg_in_map_addr() → int[source]

Get external trigger input map address

Parameters:: None –
Returns:: Current status of the external trigger input map address
Return type:: int
Raises:: Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

reset_trigger_monitor_count(address: int) → None[source]

Reset external trigger monitor counter

Parameters:: address (int) – Address of the trigger which count has to be reset
Return type:: None
Raises:: Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_trigger_monitor_count(address: int) → int[source]

Get trigger monitor count

Parameters:: address (int) – Address of the trigger
Returns:: Current status of trigger monitor counter
Return type:: int
Raises:: Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_trigger_monitor_latest() → int[source]

Get trigger monitor latest value

Parameters:: None –
Returns:: Latest value from the trigger monitor counter
Return type:: int
Raises:: Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_assembler_status(slot: int) → bool[source]

Get assembler status. Refer to the assembler log to get more information regarding the assembler result.

Parameters:

slot (int) – slot index.

Returns:

Assembler status (False = failed, True = success).

Return type:

bool

Raises:

Exception – Invalid input parameter type.
Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_assembler_log(slot: int) → str[source]

Get assembler log.

Parameters:

slot (int) – slot index.

Returns:

Assembler log.

Return type:

str

Raises:

Exception – Invalid input parameter type.
Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_current_afe_temperature(slot: int) → float[source]

Get current AFE temperature.

Parameters:

slot (int) – slot index.

Returns:

current

Return type:

float

Raises:

Exception – Invalid input parameter type.
Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_maximum_afe_temperature(slot: int) → float[source]

Get maximum AFE temperature.

Parameters:

slot (int) – slot index.

Returns:

maximum

Return type:

float

Raises:

Exception – Invalid input parameter type.
Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_current_lo_temperature(slot: int) → float[source]

Get current LO temperature.

Parameters:

slot (int) – slot index.

Returns:

current

Return type:

float

Raises:

Exception – Invalid input parameter type.
Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

get_maximum_lo_temperature(slot: int) → float[source]

Get maximum LO temperature.

Parameters:

slot (int) – slot index.

Returns:

maximum

Return type:

float

Raises:

Exception – Invalid input parameter type.
Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

start_adc_calib(slot: int) → None[source]

Calibrates ADC delay and offset values. This method sets the correct delay values for every input data index (IO data lane) in order to avoid timing violations which occur while sampling ADC data. It also calibrates offsets internal to the ADC.

Parameters:

slot (int) – slot index.

Return type:

None

Raises:

Exception – Invalid input parameter type.
Exception – An error is reported in system error and debug <= 1. All errors are read from system error and listed in the exception.

Supporting classes and functions

Please have a look at: